Star-shaped poly(lactic acid) with carboxylic acid terminal groups via poly-condensation

A series of star-shaped poly(lactic acid)s with carboxylic acid terminal groups have been synthesized by direct poly-condensation of lactic acid in the presence of a poly-carboxylic acid core molecule with triphenylphosphonium trifluoromethanesulfonate (TPP-T) catalyst.These star-polymers had thermal properties not very much different from those of star-shaped poly(lactic acid) with hydroxyl terminal groups and linear poly(lactic acid), irrespective of the structure of the core molecule and number of polymer arms. Solubility and degradability of these star-polymers were, however, greatly enhanced compared to those of star-polymers with hydroxyl terminal groups and increased depending on the number of polymer arms. From the star-shaped polymers, a variety of ammonium salts and the corresponding carboxyamides were successfully prepared.     

Behavior of composite segment for shield tunnel

Composite segment has been developed for obtaining high capacity in lining of shield tunnel subject to high hydraulic pressure and earth pressure in deep underground, which is made of steel plates connected to an infill of high fluidity concrete with shear connectors. However, a rational design method for composite segments can not be established, because the behavior of composite segments is not clarified. The purpose of this paper is to study the behavior of the most complicated composite segment with six steel plates using finite element method and the four-point bending tests. The effects of the shear studs and the thicknesses of steel plates were verified and estimated quantitatively. Meanwhile, the failure modes of composite segments were investigated. Comparisons show that the finite element model is suitable for composite segments and predicts the behavior of composite segments accurately.     

Analysis of proton exchange membrane fuel cell catalyst layers for reduction of platinum loading at Nissan

The biggest issue that must be addressed in promoting widespread use of fuel cell vehicles (FCVs) is to reduce the cost of the fuel cell system. Especially, it is of vital importance to reduce platinum (Pt) loading of catalyst layers (CLs) in the membrane electrode assembly (MEA) of a proton exchange membrane fuel cell (PEMFC). In order to lower the Pt loading of the MEA, mass transport of reactants related to the performance in high current density should be enhanced significantly as well as kinetics of the catalyst, which can result in the better Pt utilization and effectiveness. In this study, we summarized our analytical approach and methods for reduction of Pt loading in CLs. Microstructure, mass transport properties of the reactants, and their relation in CLs were elucidated by applying experimental analyses and computational methods. A simple CL model for I–V performance prediction was then established, where experimentally elucidated parameters of the microstructure and the properties in CLs were taken into account. Finally, we revealed the impact of lowering the Pt loading on the transport properties, polarization, and the I–V performance.     

Densification of rare-earth (Lu, Gd, Nd)-doped alumina nanopowders obtained by a sol-gel route under seeding

Rare-earth (RE: Lu, Gd, Nd, 0.10 mol%)-doped alumina nanopowders were prepared by a new sol-gel route using polyhydroxoaluminum (PHA) and RECl₃ solutions under α-alumina (∼ 75 nm) seeding. Among the rare-earth dopants studied, Lu yields the most suitable nanopowders for low-temperature densification. The 0.10 mol% Lu-doped nanopowders, which were obtained at a calcination temperature of 900 °C under 5 mass% α-alumina seeding, consisted of ∼ 80-nm α-alumina particles and γ-alumina nanoparticles. Using these Lu-doped alumina nanopowders, fully densified alumina ceramics with a uniform microstructure composed of fine grains with an average size of 0.61 μm could be obtained at 1400 °C by pressureless sintering. Clearly, the Lu-doped nanopowders obtained here represent a viable option for fabricating dense, finer-grained alumina ceramics because an undoped sample with 5 mass% seeds gave a microstructure with an average grain size of 1.78 μm at 1400 °C.     

Biochip with integrated pumps for plug-based sequential exchange of solutions

A novel method for exchanging solutions used in biochemical analyses and a device to carry out the exchange are proposed. An array of plugs formed using six injectors was transported in a microflow channel using a main pump located at one end of the main flow channel. The injectors and main pump were operated on the basis of the change in volume caused by the electrolysis of water. Bubbles were produced from working electrodes; these bubbles caused a diaphragm placed below the injectors to inflate and occlude the inlet of the solution reservoir. Increase in the number of bubbles caused the reservoir to inject the solution into the main flow channel in the form of a plug. Each plug was individually transported downstream to the sensing area by the main pump, which was operated in a similar manner to the injector. The device was used for the detection of a tumor marker, α-fetoprotein (AFP). Plugs of necessary solutions were individually transported to the sensing area with immobilized primary antibodies to allow antigen–antibody binding, cleaning, and detection. The fluorescence intensity from the antibodies showed clear dependence on the concentration of AFP. The immobilization of antibodies could also be carried out on-chip.     

A new recovery process of carbon dioxide from alkaline carbonate solution via electrodialysis

Bipolar membrane electrodialysis is applied to CO₂ recovery from alkaline carbonate solution. CO₂ in flue gas is captured by an alkaline hydroxide absorbing solution to form an alkaline carbonate solution. The captured CO₂ is recovered from the alkaline carbonate solution via bipolar membrane electrodialysis, and the alkaline solution is regenerated simultaneously. To reduce the power requirement for CO₂ recovery, this study considers optimal design and operation. Three membrane arrangements were compared, and the results indicate the membrane arrangement comprising a bipolar membrane and cation exchange membrane is the most energy saving. With further optimization of operation conditions, the minimum power requirement for CO₂ recovery was reduced to 2.1 MJ/kg‐CO₂ (or 2.1 GJ/t‐CO₂). © 2009 American Institute of Chemical Engineers AIChE J, 2009     

Adsorption properties of amphiphilic polyoxyalkylenated dimethylpolysiloxane derivatives on keratin

Adsorption properties of two types of dimethylpolysiloxane backbone derivatives, perfluoroalkyl polyoxyethylenated dimethylpolysiloxane (FPD) and polyoxyethylenated dimethylpolysiloxane (PD), onto keratin surfaces were investigated. Both polymers are amphiphilic, since they possess hydrophilic polyoxyethylene groups. FPD contains a perfluoroalkyl group that provides both water-and oil-repellent properties, whereas PD lacks these groups. Adsorption properties of these polymers onto keratin surfaces are considered a good index to evaluate these compounds as nonionics used in hair-coating agents, since keratin is a major component of hair. FPD was more likely to be adsorbed and less likely to be eliminated from the keratin surface than PD. Once FPD had been adsorbed onto the keratin surface, it was very slowly washed from the surface when it was immersed in stationary water, whereas PD polymers were quickly washed from the keratin surface. Even in running water, rapid elimination of FPD was not observed. The strong resistance to loss of FPD after washing with a large quantity of water may be due to the water-repellent nature of the perfluoroalkyl groups. As a comparison, FPD adsorption onto a glass surface was also investigated. The affinity to the glass surface was found to be less than to the keratin surface.